Features

    • Very high reliability, designed for long life at full power
    • EMC surpasses CE requirements: low emission & high immunity
    • Protected against all overload and short circuit conditions
    • Excellent dynamic response to load changes
    • Very low output ripple and spikes

    • 2 outputs: series mode, parallel mode or dual mode
    • Redundant parallel operation with external diodes
    • Remote control with an external potentiometer
    • Bench operation with bench adapter (optional)
    • Euro rack or wall mounting
    • Convection cooling

Single phase input 185-264 Vac (48-62 Hz)
100-132 Vac (48-62 Hz)
Efficiency up to 84% (at full load)
Output ripple and spikes from 5 mVrms / 20 mVpp
Regulation from 10 mV (0-100% load step)
Recovery time from 100 μs (50-100% load step)
Output voltage and current stability 50.10-5
MTBF 1.000.000 hrs
Operating ambient temperature -20 to +50 °C

Power supply standard EN 61204-3
Generic Emission EN 61000-6-3 (EN 55022B)
Generic Immunity EN 61000-6-2
Safety EN 60950 / EN 61010
Insulation input / output 3750 Vrms
Enclosure IP20

Width = 36 mm
Height = 75SX: 3U / 150SX: 6U
Depth = 172 mm
Weight = 75SX: 0.6 kg / 150SX: 1.2 kg

Available units

  Partnumber Voltage range Current range
  75 SX 5

3.5 – 6 V

13 A
  75 SX 15-15

2x    6 – 15 V

2.5 A
  150 SX 5

3.5 – 6 V

26 A
  150 SX 15-15

2x    6 – 15 V

5 A
  150 SX 75-75

2x    15 – 75 V

1 A
  150 SX 200-200

2x    35 – 200 V

0.3 A
  ST 150 3.5 – 6 V
2x    6 – 15 V		 13 A
2.5 A

Options

Mounting options SX-Series
 

Using a special front panel, it is possible to position the SX-units in a Eurorack. Accessories needed for Eurorack mounting:

    • F 8-3 for 75SX
    • F 8-6 for 150SX
    • F 8-6 T for ST150

Using special accessories, it is possible to position the SX-units on a wall or plate. Accessories needed for wall mounting:

    • CL 15 to fix H15-connector
    • W 8-3 for vertical wall mounting 75SX
    • W 8-6 for vertical wall mounting 150SX
    • H 95 kit for flat wall mounting 75SX
    • H 155 brackets for flat wall mounting 150SX

Using special accessories, it is possible to position the SX-units on a rail. Accessories needed for rail mounting:

    • CL 15 to fix H15-connector
    • AR 1 adapter for rail mounting
    • W 8-3 for rail mounting 75SX
    • W 8-6 for rail mounting 150SX

By connecting a special adapter, it is possible to use the SX-units on a bench. Accessory needed for bench:

    • BA 75 for 75SX
    • BA 150 for 150SX15-15 & ST150
    • BA 150 for 150SX5, 150SX75-75 & 150SX200-200

The SX-Series is standard packed with a H 15 mating connector with faston tabs (included in the price). The following connectors are optional:

    • H 15 with screw connections
    • H 15 with solder pins

Downloads

Downloads Document format Size
Data sheet SX-Series PDF (Acrobat Reader) 779.3 KB