RAT2-Z
• 1C * 2 (2 niezależne obwody)
• Super miniaturowa płytka drukowana typu bliźniaczego
• Kompaktowe i wysokowydajne przełączanie obciążenia 25 A
• 2 pojedyncze, niezależne przekaźniki w 1 obudowie
Coil data |
|
|---|---|
| Rated voltage | 12 V |
| Rated current | 2: 109 mA, 3: 75 mA, 4: 54.5 mA |
| Operating power | 2: 1309 mW, 3: 900 mW, 4: 655 mW |
| Response voltage | 2: 5.5 V DC, 3: 6.5 V DC, 4: 7.7 V DC |
| Drop out voltage | 2: 0.6 V DC, 3: 0.8 V DC, 4: 0.8 V DC |
| Coil resistance | 2: 110 Ω ±10%, 3: 160 Ω ±10%, 4: 220 Ω ±10% |
| Usable voltage range | 10 ~ 16 V DC |
| Operating time | Max. 10 ms |
| Release time | Max. 10 ms |
Contact data |
|
| Contact configuration | 1C × 2 (2 independent circuits) |
| Contact material | Ag alloy |
| Nominal switching capacity | N.O.: 20 A 14 V DC, N.C.: 10 A 14 V DC |
| Max. carrying current ※1 | 25 A for 2 min (12 V DC, 20 ℃) |
| Min. load ※2 | 1 A 14 V DC (20 ℃) |
| Rated contact voltage | 14 V DC |
| Contact resistance | N.O.: Typ. 4 mΩ, N.C.: Typ. 5 mΩ (DC 6 V 1 A) |
| Mechanical life | Min. 1,000,000 ops. (at 120 cpm) |
| Electrical life ※3 | Resistive load: Min. 100,000 ops. (at nominal switching capacity, operating frequency: 1s ON, 9s OFF) |
| Motor load: Min. 100,000 ops. (25 A 14 V DC at motor lock condition, operating frequency: 0.5s ON, 9.5s OFF) | |
General data |
|
| Rated withstand voltage (Between contacts) | 500 Vrms for 1 min (Detection current: 10 mA) |
| Rated withstand voltage (Coil / Contact) | 500 Vrms for 1 min (Detection current: 10 mA) |
| Insulation resistance | Min. 100 MΩ (500 V DC, Measurement at same location as “Rated withstand voltage” section) |
| Vibration | Functional test: 10 ~ 100 Hz, Min. 44.1 m/s2 {4.5G} (Detection time: 10 µs) |
| Destructive test: 10 ~ 500 Hz, Min. 44.1 m/s2 {4.5G} (Detection time: X, Y direction 2 hours, Z direction 4 hours) | |
| Shock | Functional test: Min. 100 m/s2 {10G} (Half-wave pulse of sine wave: 11 ms, detection time: 10 µs) |
| Destructive test: Min. 1,000 m/s2 {100G} (Half-wave pulse of sine wave: 6 ms) | |
| Ambient temperature (Operation) ※4 | Standard type: -40~85 ℃, |
| High heat-resistant / Pin in Paste type: -40~110 ℃ | |
| Operating humidity | Standard type: 5~85%, |
| High heat-resistant / Pin in Paste type: 2~85% | |
| Dimension L×W×H (mm) | 13.6×12.1×14.0 |
| Weight (g) | 6.5 |
| ※1 Depends on connection conditions. Also, this does not guarantee repeated switching. We recommend that you confirm operation under actual conditions. ※2 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. ※3 Do not use for lamp loads, electric discharge lamp loads, any other lamp loads and capacitor loads. Please contact us for details. ※4 The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. ※5 If the relay is used continuously for long periods of time with coils on both sides in an energized condition, breakdown might occur due to abnormal heating depending on the carrying condition. Therefore, please inquire when using with a circuit that causes an energized condition on both sides simultaneously. |
Model designation |
Contact arrangement |
Contact specification |
Heat resistance |
Coil resistance |
| RAT2 | -Z | * | H | 2 |
| RAT2 | C: 1C×2 (8pin) | Blank: Standard type | Blank: Standard type | 2: 110Ω |
| Z: 1C×2 (10pin) | H: High heat-resistant type | 3: 160Ω | ||
| R: Pin in Paste type | 4: 220Ω |
